Engbo MAXI 34-series Specifikace stáhnout pdf (Strana 10)

SP Windlass Control Unit v1.0.0 2015

Troubleshooting

If the windlass still does not work normally after you have tried these procedures, the fault is in the windlass itself. Contact

your nearest dealer.

FAULT SYMPTOM FAULT CODES/STATUS SOLUTION

Windlass does not operate "Power"LEDnotlit Check:

Mainswitch/breakerisengaged.

Checkbatteryfuses.

Visuallyinspectcablesandverifythatterminalsaretight.

Measurebatteryvoltage.

"Power"LEDlit Turnonpanel/remotecontrol(seeusermanual)

Seebelow:

Windlass only runs for 0,5 seconds

when pressing "IN"

None Checkcontrolpanelconnections.Signalsfor"IN"and"OUT"mightbe

swapped.

When pressing "OUT" free fall is not

engaged.

Or: When pressing "IN", motor is

running but gypsy is not turning

None SwapmotorcablesD1andD2onthecontrolunit

Windlass has poor performance “Lowvoltage” Voltagehasdroppedbelow9V

Checkbatteries.

None Measurebatteryvoltagewhileoperatingthewindlass.Ivoltagemeasure

below11V/22V,allowbatteriestocharge.

Ifthebatteryvoltageisacceptable,measurevoltageonthemotortermi-

nals,cablevoltagedropshouldbelessthan1Vwhenmotorisrunning.

Windlass releases anchor, but do

not wind in

None Checkthatendstopsensorisnotactive(Indicatedby"EndStop"LEDon

controlunitorLEDbuiltintothesensor.)

Checksensorconnectionsonthecontrolunit.

SensorLEDshouldnotbelitifnometalobjectispresentinfrontofit.

Windlass wind past endstop None Checkthattheendstopwirewoundaroundtheropeisintact.Pulltherope

withendstopwireovertheendstopsensorandverifythat(«EndStop»LED

lightup)

Adjustsensorclosertotheropeifneccesary.

Windlass releases anchor, but stops

immediatly when pressing "IN"

Noneor“Lowvoltage” Ifthebatteryisinpoorconditionitmightmeasure12/24Vwhenwindlass

isnotinuseandstillexperinceasignicantvoltagedropwhenthemotor

starts(suchvoltagedipsmightbediffculttomeasure)Thistypeofvoltage

dropscanleadtofalsetriggeringoftheendstopsensor.

Windlass stops during operation “MotorOverload” Currentlimitationhastriggered.

Thismeansthatthewindlassisoverloaded.Tryagainwithreducedload.

Ifthisfaultistriggeredwhilethewindlassislightlyloaded,itmightindicate

amechanicalfailure.

“ControllerOvertemp” Thecontrolunittemperaturesensoristoowarm.

Letthecontrollercooldown,andtryagain.

“MotorOvertemp” Themotoristoohot.

Thewindlasscontrollercalculatesmotortemperaturedependingonload

anruntime.

Letthewindlasscooldown.

“ControllerOverload” Thisfaultindicatesthattheinternalprotectionofthecontrrollerhastrig-

gered.Thiscanbecausedbyexccessivesurroundingtemperatureandhigh

load

“RuntimeExceeded” Signal"OUT"or"IN"havebeencontinuousformorethan5minutes.Thisis

aprotectionagainstpossiblefaultycontrolsignals.Re-activationispossible.

Abnormal noise during operation Thewindlassmustbeserviced.

Windlass operates, but rope is not

wound in

Theropecanslipinthegypsyifthewindlassismountedincorrectly.

Anchor is not released Theanchormightnotreleasefromthebracketifmountedincorrectly.

Note! Main switch/braker must be disconnected whenever working on the windlass mechanical parts

1 2 ... 5 6 7 8 9 10 11 12

Komentáře k této Příručce

Žádné komentáře

Engbo MAXI 34-series Specifikace Strana 10

Komentáře k této Příručce

Související produkty a manuály pro ne Engbo MAXI 34-series